Validating Meyl's Device

On coil B, at 13MHz, the LED at receiver side turns on and the transceiver side turns off. The measurement shows that there is overunity. This is verified by hooking on the same scope channel. (My scope has slight error on different channel) However, then i switched to AC load the power is so much less and no overunity. I wonder why the voltage can turn lower than Vf of LED when I used AC load. Hooking up the probe will turn off the LED and I have to invert the polarity. Could this probing cause the AC load to be low? I remember switching to AC load the transmitter LED turns on. When the probe sucks the power from receiver's LED did the transmitter LED turns on ? Answer: The scope connects the ground point between the channel. Hence, it affects the measurement when we change the polarity.
Coil B @14Mhz without the metal ball, when the transmitter primary and receiver load ground are connected, the LED will turn on. Overunity observed.

Coil B @13Mhz and 20cm ground wire, the transmitter's LED will light up when I switched to AC and DC load. But for LED, the transmitter's LED will turned off. When I used 1m ground wire, the transmitter LED will never turn on regardless of AC load,DC load or LED at receiver side. Slight overunity observed when used with 1m ground wire. However when the amplitude is pumped up the overunity is less obvious. Overunity disappeared with higher amplitude. How about 6m ground wire?

It is weird to see that when I put the jumper for LED on transmitter side the power consumption is reduced compared to without LED jumper and the receiver power increased. Trying with LEDs in parallel does not affect the overunity power. What if the LED is in series, can I pump up the amplitude while maintaining overunity?

Does square wave improve overunity because of fast rise time and back EMF?

Update on Steven Mark's TPU

The patent was not sold to MPI. MPI maintain a different technology. Steven Mark refers to Valve Amplifier 3rd Ed. pg 262, "The inrush of current through the filament interacts with the earth's magnetic field to produce a small kick." This small kick is huge when you have multiple kick added together.

Steven understands Tesla impulse current in Edison's DC generator. The kick came out of the wire perpendicularly. The kick is about how fast the capacitor discharged and how fast Tesla stops the current flow AT the spark gap. His goals were to get the time in which the discharge is STOPPED to be much quicker. As Tesla did this he found that the perpendicular radiations, the ones from the wires, caused electrical effects to appear in wires and other copper/metal materials near the STOPPED current/discharge. These electrical effects could be made to create electrons on other wires and copper around his STOPPED current/discharge wire.

This looks like cross talk effect by impulse current.

Theory on Wardenclyffe Failure

The story is frequently told that when Morgan found out from Tesla that the true purpose of the Wardenclyffe transmitter was to provide free electricity to the world, he abruptly pulled the funding. That's not completely accurate. The economic conditions were recessionary at the time and the stock market had taken a considerable dip that year. Morgan wasn't interested in risking any more capital in perilous times on a project he couldn't fully fathom and wasn't completely convinced of. Tesla held land ownership of the Wardenclyffe site and tower, but no further work was done after 1910. In 1914, Tesla was deeply in debt and signed over the deed of Wardenclyffe Station to pay off years of back rent due to the owners of the New Yorker Hotel where he was living (he occupied two penthouse suites in the hotel). In 1917, the hotel owners had the tower demolished and its parts sold for salvage. Despite the loss of Wardenclyffe, Tesla continued to refine his understanding of Radiant Energy and miniaturize the equipment needed to produce it. He eventually was able to reduce the equipment down to the size of a suit case.
http://www.rense.com/general11/tesla.htm

Time Reversal

What is time reversal? According to TD Lee, time reversal is lika a film on a drop of water from faucet hitting the sink and making a splash, when shown backward, start from gathering of splash, reform the drop and goes back to faucet.

Secret about Tesla Magnifying Transmitter

Even by closing the loop on the spiral pancake coil, the overunity still exists. This really defy the current known circuit theory since any transformer can yield higher output power.